Auto dent pulling machine

SmartPuller dent pulling machine enables the dent pulling of almost any area throughout the vehicle body in all needed directions. It is a new and unique auto dent repair system made by Autorobot. This new innovation makes the repairing of vehicle panels and box structures faster and more economical.

Our dent puller enables the dent repair of vehicle front parts, box structures, side structures, rear end, rear corners, roof structures and car doors. When stronger pull is needed, double pull can be used to create more pulling power.

Pulling a dent - how does it work?

Using the dent pulling system is made easy with SmartPuller.

An easy use of the equipment has been achieved with the movable stand with the wheels and the adjustable rubber pads.

Compact structure of SmartPuller enables very easy use. All equipment needed for support and dent pulling can be adjusted to correct height, where they stay without holding. Autorobot SmartPuller needs a resistance welder for fixing the washers or welding wire to the area to be pulled.

The speciality of SmartPuller is its ability to pull dents almost all over the body in all needed directions.

Pulling method

Smartpuller has unique method of pulling dents. See below more specific details.

The lower rubber pads (A) of SmartPuller have been adjusted to the proper width and height, after which it has been pushed to the strong point near the area to be pulled. The straightening support (B) has also been set to the roof structure of the car in the height and width direction. 

After this, the pulling screw (C) has been adjusted to the place that is to be pulled. The actual pulling is done with the crank handle (D). A grapple such as welding wire for pulling, pulling gripper or adhesive cup holder can be attached to the holder on the end of the screw (E), based on the kind of target area to be pulled.

The straightening support (1) of SmartPuller is placed on the strong body area to achieve the best possible dent pulling result. Dent pulling direction can be freely chosen.

The straightening support is easily adjustable in the vertical beam (2) as well as adjusting the straightening rubber pads downwards, which allows straightening pull to the right direction. Choosing stepless pulling line speeds up the straightening.

The straightening support is easily adjustable in the vertical beam (2) as well as adjusting the straightening rubber pads downwards, which allows straightening pull to the right direction. Choosing stepless pulling line speeds up the straightening.

See the dent pulling sets and equipment we have to offer. 

Double pull method

For the targets needing stronger pulling power, double pull with two pulling screws can be used. The possibility for double pull enables wider usage area of SmartPuller for even more demanding repair jobs. The force of two pulling screws is over 1000 kg/2205 lbs. That much pulling power often is sufficient for the targets shown in the pictures below.

The second pulling screw set including gripper (see the image above) you can order as accessory. Check out all the accessories.

How can SmartPuller help with repairing vehicle dents?

With SmartPuller you can repair wide range of areas of damaged vehicle. Below you can find a detailed list of different car dent pulling areas you can work easily with SmartPuller:

• Vehicle front parts
• Box stuctures
• Rear end and rear corners
• Roof structures
• Car doors

Vehicle front and front parts

Vehicle front

Rubber pads (C) equipped with adjustment and located in the vertical beam (B) of SmartPuller enable fast straightening support. This allows various dent pulling jobs without the need to mount the vehicle onto the collision repair system.

For dent pulling of bonnet lock plate and other front parts of the vehicle, also the McPherson fastening bolt can be uset for upper support.

Fasteners are available as accessory: Fastening set No. A-14+11-1.

SmartPuller works also in dent pulling of vehicle bonnets and trunk lids.

To repair lengthwise damage on them, another pulling gripper No. H31+ must be obtained as accessory.

Vehicle front parts

Dent pulling of vehicle front parts happens by installing the upper support e.g. to vehicle front panel or to McPherson fastening pillar and by installing the lower support as shown in the picture.

The possibility for double pull enables wider usage area of SmartPuller for even more demanding dent pulling jobs. In the picture you can see in use a second pulling screw set including gripper (available as accessory).

Box structures

Unbeatable variety of pulling angles

SmartPuller technology enables e.g. dent pulling of box structures to all needed directions. The structure of adjustable rubber pads allow them to take a shape that will not damage the supporting area. For more demanding dent pulling it is possible to use two pulling screws. For the targets that have little pulling space only, a short pulling screw (A) can be used (see pictures 2 and 4).

Rear end and rear corners

Rear end

By using a telescope tower (1) for dent pulling of vehicle rear end, you can get upper support (2) to a strong area. This enables choosing the best possible straightening line in height and width directions. Dent pulling will take place with one or two pulling screws.
The second gripper H31+ and pulling screw A-11+1 are available as accessories.

Rear corners

Dent pulling of numerous vehicle corner damages succeeds when using for upper support the beam (B), on the end of which an aluminium angle piece (C) is to be placed. To angle piece (C), you will attach Gripper H31+ and the gripper is fastened to the frame of the rear part.

Roof structures

Badly damaged vechile roof panels

Car door dent repair

Handing a car door can be difficult task especially working with heavier vehicle door types.

Additional Set of car door handling makes dent pulling of vehicle doors very easy, e.g. when changing doors. Placing the door is easy when you can adjust the door height with screw (A).

Easy height adjustments for easy door handling

in the upper holder (C) the frame of the car door can be raised or lowered in padded holder when adjusting the height. The lower holder (B) of the car door is equipped with padding, thanks to which the set works well also with painted doors.

The picture above shows how SmartPuller additional set functions in handling heavy vehicle doors, where multifunctional holder is used to press from the upper frame of the door.

This picture shows how the door can be easily moved to the desired place for further handling after removing it.

SmartPuller equipped with the wheels makes the transfer easy.

Take a more detailed look to dent pulling of vehicle doors